Albott 9100 BTU Mini Split Air Conditioner and Heater (Model SAC011) User Manual

1. Sản phẩm hếtview

The Albott 9100 BTU Mini Split Air Conditioner and Heater is an inverter heat pump system designed for efficient temperature control in spaces up to 450 sq. ft. It offers both cooling and heating functionalities, smart control options, and quiet operation.

• Khả năng tương thích thông minh: Control the unit remotely via smartphone or voice assistant (Alexa compatible). Initial Wi-Fi connection requires being on the same network.
• Hiệu suất tiết kiệm năng lượng: With a SEER2 rating of 20.5, it consumes 850W for cooling and 770W for heating, promoting energy efficiency.
• Hoạt động yên tĩnh: Designed for low-noise performance, ideal for bedrooms and offices.
• Làm mát và sưởi ấm hiệu quả: Provides 9,100 BTU for cooling and 9,500 BTU for heating for year-round comfort.
• Công nghệ tự làm sạch: Features a 135°F self-cleaning function that removes dust buildup and reminds users every 500 hours to activate a 30-minute cleaning cycle.

2. Có gì trong hộp

The Albott Mini Split system comes in two boxes and includes all necessary components for installation and operation:

• Đơn vị trong nhà
• Đơn vị ngoài trời
• Hướng dẫn sử dụng
• Điều khiển từ xa và pin
• Hanging plate for indoor unit
• Drain pipe for indoor unit
• Bản vẽ kích thước lắp đặt
• 14.76 Ft communication wires
• Tay áo tường
• Bột trét
• Copper connection pipe - air pipe
• Copper connection pipe - liquid pipe
• 8.2 Ft power cord
• Băng dính
• Wi-Fi USB

Image 1: All components included in the Albott Mini Split Air Conditioner and Heater package.

3. Thông số kỹ thuật

Image 2: Detailed product dimensions and electrical specifications.

4. Cài đặt và thiết lập

Proper installation is crucial for the optimal performance and longevity of your Albott Mini Split system. It is recommended to consult a professional HVAC technician for installation to ensure compliance with local regulations and safety standards.

4.1 Hướng dẫn Cài đặt Chung

• Ensure the installation location for both indoor and outdoor units is hard, flat, and firm to prevent vibration and noise.
• Avoid installing near heat sources, steam sources, or areas with flammable/explosive gases.
• Maintain adequate clearance around the units for proper airflow (refer to specific diagrams in the full manual).

4.2 Lắp đặt dàn lạnh

1. Tấm lắp: Securely fix the mounting plate to the wall using at least 5 expansion screws. Use a level to ensure it is horizontal.
2. Khoan lỗ tường: Drill a wall hole for the refrigerant pipes and wires. Ensure the hole is inclined outward by 5-10 degrees and has a diameter of 60-80mm. Avoid wires, plumbing, and gas lines.
3. Cáp kết nối: Pass the power cable from the back of the indoor unit and fix it to the terminal board. Secure the cable with a clamp.
4. Đường ống làm lạnh: Connect the copper pipes to the indoor unit. Tighten the taper nuts with fingers first, then use two wrenches to fully tighten to the specified torque (refer to the torque table in the full manual).
5. Ống cống: Connect the drain hose to the water outlet pipe and secure it with adhesive tape. Ensure the hose is sloped down to prevent water leakage.
6. Viền trang trí: Wrap the refrigerant piping, wires, and drain pipe together with wrapping tape.
7. Lắp đặt dàn lạnh trong nhà: Carefully put the refrigerant piping through the wall hole and mount the indoor unit onto the mounting plate. Push the lower part until a 'click' sound is heard to ensure it's firmly fixed.
8. Seal Wall Hole: Use the pipe protecting ring and putty to seal the wall hole around the pipes and wires.

4.3 Lắp đặt dàn nóng

1. Chọn địa điểm: Install the outdoor unit in a firm and flat place to prevent vibration and noise. Ensure proper clearances (e.g., >20cm to obstruction, >10cm air in side, >200cm air out side).
2. Cài đặt giá đỡ: If mounting on a wall, install the outdoor unit bracket using at least 6 expansion bolts. Use a level to ensure it is horizontal and vertical.
3. Fix Outdoor Unit: Đặt dàn nóng lên giá đỡ và cố định chân đế bằng 4 vít.
4. Kết nối đường ống dẫn môi chất lạnh: Remove the nuts from the stop valves. Aim at the pipe center of the stop valve, tighten the taper nut with fingers, then use two wrenches to fully tighten to the specified torque.
5. Fix Cables: Remove the electrical box cover. Fix the cables to the terminal board according to the wiring diagram provided inside the box cover. Use clampdùng để sửa cáp.

4.4 Vacuuming and Refrigerant

1. Kết nối bơm hút chân không: Connect the stop valve, charging hose, manifold valve, and vacuum pump as shown in the diagram (refer to full manual for diagram).
2. Hút bụi: Turn on the handle Lo to vacuumize for at least 15 minutes. Ensure the pressure gauge value is ≤0.1MPa (-76cmHg / 500μm). Keep the pressure for 3-5 minutes after vacuumizing; pressure springback should be ≤0.05MPa.
3. Mở van: Open the 1/4 liquid valve and remove the charging hose. Then, open all the liquid and gas valves. Screw all the caps and tighten them up.

Note on Refrigerant Adjustment:

When the length of the connecting pipe is changed, an extra amount of refrigerant may need to be added or reduced to maintain optimal operation. Refer to the table below:

5. Hướng dẫn vận hành

Your Albott Mini Split system offers various modes and features for customized comfort.

Image 3: Remote control and its various functions.

5.1 Chức năng điều khiển từ xa

• Chế độ: Auto, Cool, Heat, Dry, Fan, Sleep, Eco.
• Tốc độ Quạt: Low, Mid, High, Turbo.
• Điều chỉnh nhiệt độ: Use the SET buttons to increase or decrease temperature.
• Lung lay: Adjust horizontal and vertical airflow direction.
• Bộ đếm thời gian: Đặt hẹn giờ 24 giờ để bật/tắt tự động.
• Trưng bày: Toggle the unit's display on/off.

5.2 Điều khiển thông minh

The unit can be controlled via a smartphone app or voice assistants like Alexa. Ensure the unit is connected to your Wi-Fi network (initial setup requires being on the same network).

5.3 Chế độ hoạt động

• Chế độ mát: Cools down to 60°F.
• Chế độ nhiệt: Heats up to 90°F.
• Chế độ khô: Loại bỏ tới 42 pint độ ẩm mỗi ngày.
• Chế độ quạt: Circulates air with 4 adjustable wind speeds.
• Chế độ ngủ: Provides quiet operation for undisturbed rest.

Hình 4: Hếtview về chức năng 4 trong 1.

6. Bảo trì

6.1 Chức năng tự làm sạch

The unit features a 135°F self-cleaning function to prevent dust buildup and maintain efficiency. The system will remind you every 500 hours of operation to activate a 30-minute automatic cleaning cycle.

Image 5: Illustration of the automatic self-cleaning process.

6.2 Water Drain and Leakage Test

During trial operation, it is important to check the water drain and test for any leakage. Pour approximately 500ml of water along the evaporator (about 20 seconds) and verify that water flows out normally from the drain pipe and that there is no leakage around the indoor unit.

KHAI THÁC. Xử lý sự cố

If you encounter any issues with your unit, refer to the full instruction manual for detailed troubleshooting steps. For immediate safety concerns, such as electricity leakage, turn off the power supply to the unit immediately and contact qualified personnel for examination.

8. Bảo hành và Hỗ trợ

The Albott Mini Split Air Conditioner and Heater comes with a 5-year parts coverage Và 8-year compressor support. For any warranty claims or technical assistance, please refer to the contact information provided in your full instruction manual or visit the official Albott webđịa điểm.