Hướng dẫn sử dụng máy khắc laser SCULPFUN S30 và màn hình cảm ứng TS1.

1. Giới thiệu

This manual provides essential information for the safe and effective operation of your SCULPFUN S30 Laser Engraver and TS1 Touch Screen. Please read this manual thoroughly before assembly, operation, or maintenance to ensure proper usage and to prevent damage or injury.

Safety Warning: This product is a Class IV laser device. Direct exposure to the laser beam can cause severe eye damage and skin burns. Always wear the provided laser safety goggles during operation. Ensure proper ventilation and never leave the machine unattended while operating.

Image 1.1: SCULPFUN S30 Laser Engraver with TS1 Touch Screen. The image displays the assembled laser engraver with a workpiece on its bed, alongside the separate TS1 touch screen controller.

2. Thành phần sản phẩm

The following items are included in your package. Please verify all components upon receipt.

• 1 x S30 Laser Engraver Unit
• 1 x Laser Repair Kit
• 1 x 12V Automatic Air Pump
• 3 x A4 size 3mm Wood Boards
• 2 công tắc giới hạn
• 1 x Bộ đổi nguồn 12V 5A
• 1 x Power Cord
• 1 x Cáp USB
• 1 x Air Pipe
• 1 x Bộ công cụ cài đặt
• 1 x Kính bảo hộ laser
• 1 x A4 Metal Backing Plate
• Installation Package (Steps 1-6)
• 1 x User Manual (for S30)
• 1 x X-axis Assembly
• 2 x X Profiles
• 2 x Y Profiles
• 1 x Bộ hộp điều khiển
• 3 x Chân hỗ trợ
• 1 x TS1 Touch Screen
• 1 x Power Cord (for TS1)
• 1 x Thẻ SD
• Đọc 1 x Thẻ
• 1 x User Manual (for TS1)

3. Thông số kỹ thuật

Máy khắc laser SCULPFUN S30

• Công suất đầu ra của diode laser: 5W (năng lượng ánh sáng)
• Tập trung tia laser: 0.06x0.06mm
• Bước sóng laser: 455 ± 5nm
• Phương pháp tập trung: Cột tiêu cự cố định + thiết bị trượt
• Bảo vệ bằng tia laze: Detachable laser protection cover, adjustable/removable goggles
• Công suất đầu vào: 100-240V AC, 50/60Hz
• Đầu ra: 12V 5A
• Độ chính xác khắc: 0.005mm
• Standard Engraving Area: 410x400mm (expandable to 935x400mm or 935x905mm with extension kits)
• Công suất điện của máy: Khoảng 60W
• Loại máy bơm khí: Điều khiển bằng bo mạch chủ, 12V, lưu lượng 30L/phút
• Đường kính bên trong của ống khí: 7.5mm
• Bo mạch chủ: 32-bit air-assisted, reserved for offline control (Bluetooth, SD card - upgrade package sold separately)
• Phần mềm điều hành: LightBurn (with M8 air assist function), LaserGRBL, Benbox, GrblController, LiteFire
• Hệ điều hành được hỗ trợ: Windows, MAC
• Được hỗ trợ File Định dạng: NC, BMP, JPG, PNG, DXF, and other image formats
• Truyền dữ liệu: Kết nối USB hoặc kết nối không dây Bluetooth
• Kích thước sản phẩm: 18.11 x 18.11 x 6.69 inch

Image 3.1: Illustration of the S30's 5W laser beam shaping technology, highlighting its high density and sharp focus for effective cutting and engraving.

SCULPFUN TS1 Touch Screen

• Chất liệu sản phẩm: ABS+PC
• Kích thước màn hình: 3.5 inch
• Chất liệu màn hình: Màn hình cảm ứng điện dung
• Độ phân giải màn hình: 480x320
• Kích thước sản phẩm: 126x89x25mm
• Kết nối: Offline engraving via SD card, WiFi connectivity for mobile app control

Image 3.2: The SCULPFUN TS1 Touch Screen, showing its compact design and user interface for controlling the laser engraver.

4. Thiết lập

4.1. Assembly of the S30 Laser Engraver

Refer to the included "Step 1-6 Installation package" and the S30 user manual for detailed assembly instructions. Ensure all screws are tightened and connections are secure. The assembly typically involves:

1. Assembling the X and Y profiles để tạo thành khung.
2. Mounting the control box assembly and support feet.
3. Installing the X-axis assembly and laser module.
4. Connecting the limit switches and wiring.
5. Attaching the air pump and air pipe.

4.2. Connecting the TS1 Touch Screen

The TS1 touch screen connects to the S30 laser engraver via a USB cable. Plug one end of the USB cable into the S30 control box and the other end into the TS1. Connect the TS1 to its power adapter and plug it into a power outlet.

4.3. Cài đặt phần mềm

For computer-controlled operation, install LightBurn or LaserGRBL software on your Windows or MAC system. Follow the software's installation guide. Ensure your computer's USB drivers are up-to-date for proper communication with the engraver.

5. Hướng dẫn vận hành

5.1. Chuẩn bị vật liệu

Place the material to be engraved or cut on the metal backing plate within the engraving area. Ensure the material is flat and securely positioned to prevent movement during operation. For optimal results, use the provided A4 metal backing plate.

5.2. Điều chỉnh tiêu điểm tia laser

The S30 features a fixed focus column and sliding device for focusing. Adjust the laser module's height until the focus column touches the material surface. This sets the optimal focal distance for the 0.06x0.06mm laser spot.

5.3. Automatic Air Assist Operation

The S30 is equipped with an automatic air assist system. This system can be controlled via the M8 command in LightBurn software. Air assist significantly improves cutting performance by clearing debris and reducing charring.

Image 5.1: The S30 laser engraver demonstrating automatic air assist. The image shows the laser module with air assist active during cutting and inactive during engraving, controlled by software settings.

Image 5.2: A visual comparison illustrating the benefits of automatic air assist over manual air pump control, showing cleaner cuts and edges with automatic control.

For engraving, air assist is typically turned OFF to achieve finer detail. For cutting, air assist is turned ON to increase cutting speed and produce cleaner edges.

5.4. Engraving and Cutting Materials

The S30 can engrave on a variety of materials including wood (walnut, cherry, MDF), bamboo, cardboard, plastic, leather, PCB board, aluminum oxide, 304 stainless steel, ceramic, and dark stone. It can cut materials such as wood, MDF, acrylic board, cardboard, non-woven fabric, bamboo sheets, leather, and some plastic boards.

5.5. Using the TS1 Touch Screen for Offline Control and WiFi

The TS1 touch screen enables offline operation and WiFi connectivity.

• Khắc ngoại tuyến: Lưu lại hình khắc của bạn files to the provided SD card. Insert the SD card into the TS1. You can then select and initiate engraving jobs directly from the touch screen without a computer connection.
• Kết nối WiFi: The TS1 provides WiFi capabilities to the S30. When connected to WiFi, you can use the SCULPFUN mobile application to control the engraver and create designs in real-time from your smartphone or tablet.

Image 5.3: The TS1 touch screen connected to the S30, demonstrating its WiFi functionality and compatibility with a mobile application for wireless control.

6. Bảo trì

6.1. Laser Lens Cleaning

Regularly inspect the laser lens for dust or debris. Use a soft, lint-free cloth and a small amount of lens cleaning solution (e.g., isopropyl alcohol) to gently clean the lens. Avoid abrasive materials or excessive force, which can scratch the lens.

6.2. General Machine Cleaning

Keep the engraving area and linear rails clean from dust and material residue. Use a brush or compressed air to remove debris. Periodically check and clean the air pump filter if applicable.

KHAI THÁC. Xử lý sự cố

• Máy không bật nguồn: Check all power connections, ensure the power adapter is securely plugged into both the machine and a working outlet.
• Tia laser không bắn: Verify the laser module is correctly installed and connected. Check software settings to ensure the laser power is set above zero. Ensure safety interlocks (if any) are engaged.
• Chất lượng khắc/cắt kém:
• Kiểm tra tiêu cự laser.
• Adjust engraving/cutting speed and power settings in the software.
• Ensure the material is flat and stable.
• Làm sạch thấu kính laser.
• For cutting, ensure air assist is enabled and functioning.
• Máy không kết nối được với máy tính: Ensure the USB cable is properly connected. Reinstall or update USB drivers. Try a different USB port or cable.
• TS1 Not Responding: Ensure the TS1 is powered on and connected to the S30. Restart both devices.

8. Hướng dẫn an toàn

• Bảo vệ mắt: Always wear the provided laser safety goggles when the laser engraver is operating. Never look directly at the laser beam.
• Thông gió: Operate the laser engraver in a well-ventilated area to dissipate fumes and smoke produced during engraving/cutting. Consider using an exhaust system.
• An toàn phòng cháy chữa cháy: Luôn để bình chữa cháy gần đó. Không để máy không có người trông coi trong khi vận hành, đặc biệt là khi cắt vật liệu dễ cháy.
• An toàn vật liệu: Only engrave/cut materials specified as safe. Avoid materials that produce toxic fumes or are highly reflective.
• Trẻ em và vật nuôi: Giữ trẻ em và vật nuôi tránh xa khu vực phẫu thuật.
• Dừng khẩn cấp: Familiarize yourself with the location of the power switch for quick shutdown in an emergency.
• An toàn điện: Ensure the power supply is stable and matches the machine's requirements. Do not operate with damaged cables or adapters.

9. Bảo hành và Hỗ trợ

For warranty information and technical support, please refer to the specific warranty card included with your product or contact SCULPFUN customer service through their official webtrang web hoặc nhà bán lẻ nơi bạn mua sản phẩm. Hãy giữ lại hóa đơn mua hàng để làm bằng chứng mua hàng.