1. Giới thiệu
This manual provides essential information for the installation, operation, and maintenance of your HALLOMOTOR Sine Wave Intelligent EBike Controller and SW900 Display. This system is designed for 48V-72V battery systems, delivering 2000W-4000W of power with a 60A current rating and an 18 MOSFET configuration for smooth and efficient electric bicycle performance. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Sản phẩm hếtview
The HALLOMOTOR EBike Controller and SW900 Display system consists of a high-performance sine wave controller and a digital display unit. The controller manages power delivery to the motor, while the display provides real-time riding data and allows for system configuration.
Hình 2.1: The HALLOMOTOR Sine Wave Intelligent EBike Controller (bottom) and the SW900 Display (top). The controller is a black, finned aluminum casing with numerous wires extending from one end. The display is a rectangular black unit with a digital screen and control buttons on the left side, connected by a cable.
Hình 2.2: Cận cảnh view of the HALLOMOTOR EBike Controller, showcasing the extensive wiring harness. Various colored wires with different connectors are visible, including thick power cables, motor phase wires, and smaller signal wires for accessories and sensors. A yellow XT90 connector is also visible.
Hình 2.3: Dimensions of the EBike Controller. The image indicates a length of 26.5 cm, a width of 9.5 cm (including mounting bracket), and a height of 5.0 cm. The main body length is approximately 23.5 cm.
Hình 2.4: Product label on the side of the Sine Wave Controller. It displays the model number RM607260ASVPR, Rated Voltage: DC60V/72V, Maximum Current: 60±1A, Rated Current: 30A, Speed Set: 1-4.2V, Brake Input: Low-Level, and Low Voltage Protection: DC50/60±1V.
Hình 2.5: Detailed wiring diagram for the EBike Controller. Key connections are numbered and labeled: 1. Motor Cable connection (3-Phase), 2. Power Supply Cable XT90, 3. Light, 4. Electric Lock, 5. Self Learning, 6. Display, 7. Reverse, 8. Throttle, 9. Brake, 10. Cruise, 11. Speed Limit, 12. PAS (Pedal Assist System), 13. Alarm, 14. Hall sensor wires.
Hình 2.6: The SW900 Display unit. This digital display shows speed, odometer (ODO), trip distance, battery level, power output (WATT), and pedal assist system (PAS) level. It features control buttons on the left for navigation and settings.
3. Thông số kỹ thuật
| Tính năng | Đặc điểm kỹ thuật |
|---|---|
| Người mẫu | RM607260ASVPR |
| Xếp hạng Voltage | DC60V/72V (Universal Voltage) |
| Dòng điện tối đa | 60 ± 1A |
| Dòng điện định mức | 30A |
| Công suất định mức (48V) | 1382W |
| Công suất định mức (52V) | 1498W |
| Công suất định mức (60V) | 1320W |
| Công suất định mức (72V) | 2073W |
| Peak Power (48V) | 2880W |
| Peak Power (52V) | 3120W |
| Peak Power (60V) | 3600W |
| Peak Power (72V) | 4320W |
| MOSFET | 18 |
| Rotor Position Detecting Method | Cảm biến Hall |
| Bộ tốc độ | 1-4.2V |
| Đầu vào phanh | Cấp thấp |
| Âm lượng thấptage Bảo vệ | DC50V/60V ± 1V |
| Kích thước (D x R x C) | 26.5cm x 9.5cm x 5.0cm (approximate, including mounting bracket) |
| Cấp độ chống thấm nước | IP65 |
Đơn vị hiển thị: SW900 Digital Display
- Functions: Speed, Odometer (ODO), Trip Distance, Battery Level, Power Output (WATT), PAS Level.
- Compatibility: Designed to work seamlessly with the HALLOMOTOR Sine Wave Controller.
4. Thiết lập và Cài đặt
Proper installation is crucial for the safe and efficient operation of your e-bike system. If you are unsure about any steps, it is recommended to seek assistance from a qualified e-bike technician.
4.1 Biện pháp phòng ngừa an toàn
- Luôn ngắt kết nối ắc quy trước khi thực hiện bất kỳ thao tác lắp đặt hoặc bảo trì nào.
- Đảm bảo tất cả các kết nối đều an toàn và cách điện đúng cách để tránh hiện tượng đoản mạch.
- Xác minh rằng dung lượng pintage matches the controller's specified voltage phạm vi (48V-72V).
- Đeo đồ bảo hộ an toàn phù hợp, bao gồm cả kính bảo vệ mắt.
4.2 Mounting the Controller and Display
- Bộ điều khiển: Mount the controller in a location that is protected from direct water exposure and physical impact, allowing for adequate airflow for cooling. Use the integrated mounting bracket and appropriate fasteners.
- Trưng bày: Mount the SW900 display securely on your handlebar in a position that is easily visible and accessible while riding.
4.3 Wiring Connections (Refer to Figure 2.5)
- Motor Cable (3-Phase): Connect the three thick motor phase wires (typically green, blue, yellow) from the controller to the corresponding motor phase wires. Ensure correct color matching.
- Dây cảm biến Hall: Connect the smaller Hall sensor wires from the controller to the motor's Hall sensor connector. These are crucial for smooth motor operation.
- Power Supply Cable (XT90): Connect the main power cable (XT90 connector) from the controller to your e-bike battery. Ensure polarity is correct (red to positive, black to negative).
- Khóa điện: Connect the electric lock wires (if applicable) to your ignition switch or power button.
- Trưng bày: Connect the SW900 display cable to the designated display port on the controller.
- Van tiết lưu: Connect the throttle cable to the controller's throttle input.
- PAS (Hệ thống hỗ trợ đạp): Connect the PAS sensor cable to the controller's PAS input.
- Phanh: Connect the brake lever cut-off switches (if equipped) to the controller's brake input. This provides a low-level brake signal to cut motor power when braking.
- Light/Alarm/Reverse/Cruise/Speed Limit: Connect any optional accessories such as lights, alarm systems, reverse function, cruise control, or speed limit switches to their respective ports on the controller as needed.
- Self-Learning Wires: These two wires are typically used for initial motor pairing. Connect them briefly, allow the motor to spin, then disconnect. Refer to specific self-learning instructions if provided with your motor.
After all connections are made, double-check them for security and correctness before connecting the battery.
5. Hướng dẫn vận hành
The SW900 display provides an intuitive interface for controlling and monitoring your e-bike.
5.1 Bật/Tắt nguồn
- To power on the system, press and hold the power button on the SW900 display for a few seconds.
- Để tắt nguồn, nhấn và giữ nút nguồn một lần nữa cho đến khi màn hình tắt.
5.2 Chức năng hiển thị
The SW900 display shows various parameters:
- Tốc độ: Current riding speed (Km/h or Mph).
- ODO: Total odometer reading (total distance traveled).
- CHUYẾN ĐI CHƠI: Trip distance for the current ride.
- Mức pin: Biểu đồ thể hiện dung lượng pin còn lại.
- WATT: Công suất đầu ra thực tế của động cơ.
- Mức PAS: Current Pedal Assist System level (e.g., 0-5).
5.3 Adjusting PAS Level
Use the '+' and '-' buttons on the display to increase or decrease the pedal assist level. Level 0 typically means no assist, while higher numbers provide more motor assistance.
5.4 Menu Cài đặt
The SW900 display usually has a settings menu accessible by pressing a combination of buttons (e.g., power and '+' simultaneously). This menu allows for configuration of parameters such as wheel size, speed unit (Km/h/Mph), battery voltage, and more. Refer to the specific SW900 display manual for detailed instructions on navigating and adjusting settings.
6. Bảo trì
Regular maintenance helps ensure the longevity and reliable performance of your e-bike controller and display.
- Giữ sạch sẽ: Periodically wipe down the controller and display with a soft, damp vải. Tránh sử dụng hóa chất mạnh hoặc vật liệu mài mòn.
- Kiểm tra kết nối: Regularly inspect all wiring connections for tightness and signs of corrosion or damage. Ensure all connectors are fully seated.
- Bảo vệ khỏi nước: While the controller has an IP65 waterproof rating, avoid submerging it in water or exposing it to high-pressure water jets. Ensure the display is also protected from heavy rain.
- Tránh sát thương vật lý: Protect the controller and display from impacts or drops.
- Nhiệt độ: Operate and store the components within their specified temperature ranges to prevent damage.
KHAI THÁC. Xử lý sự cố
This section addresses common issues you might encounter. For more complex problems, consult a professional e-bike technician.
7.1 No Power to Display/Motor
- Kiểm tra pin: Ensure the battery is charged and properly connected to the controller.
- Kết nối nguồn chính: Verify the XT90 power cable connection is secure.
- Khóa điện: If an electric lock is used, ensure it is in the "ON" position.
- Cáp hiển thị: Check the connection between the display and the controller.
7.2 Motor Not Responding
- Throttle/PAS: Ensure the throttle is connected and functioning, and the PAS sensor is correctly installed and aligned.
- Đòn phanh: Check if the brake cut-off switches are engaged. Disconnect them temporarily to test if they are causing the issue.
- Motor Phase/Hall Wires: Verify all motor phase and Hall sensor wires are securely connected and correctly matched.
- Tự học: If the motor is new or has been disconnected, perform the self-learning procedure (briefly connect the self-learning wires, allow motor to spin, then disconnect).
7.3 Sai số trong việc đọc tốc độ/quãng đường
- Cài đặt kích thước bánh xe: Access the SW900 display settings menu and ensure the correct wheel size is configured.
- Cảm biến tốc độ: Check if the speed sensor (if external) is properly installed and functioning.
7.4 Display Error Codes
The SW900 display may show error codes. Refer to the specific SW900 display manual for a list of error codes and their corresponding troubleshooting steps.
8. Bảo hành và Hỗ trợ
For warranty information and technical support, please contact your original seller or HALLOMOTOR directly. Keep your purchase receipt as proof of purchase. Specific warranty terms and conditions may vary.
Khi liên hệ với bộ phận hỗ trợ, vui lòng chuẩn bị sẵn các thông tin sau:
- Product Model: HALLOMOTOR 60A Controller + SW900 Display
- Ngày mua hàng
- Mô tả vấn đề
- Any relevant error codes from the display
