Giới thiệu
Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.
Thông tin an toàn quan trọng
Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.
- Verify that your monitor's weight and VESA pattern are within the specified limits.
- Do not exceed the maximum load capacity of 26.5 lbs per arm.
- Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
- Use only the provided hardware.
- Để xa tầm tay trẻ em những bộ phận nhỏ.
Thông số kỹ thuật
- Người mẫu: EGCM13B
- Khả năng tương thích kích thước màn hình: 13 đến 34 inch
- Weight Capacity (per arm): Lên đến 26.5 lbs
- Khả năng tương thích VESA: 75x75 mm, 100x100 mm
- Arm Span: 33 inch
- Chiều cao cực: 16.3 inch
- Kiểu chuyển động: Tilt, Swivel, Rotation, Articulating
- Góc nghiêng tối đa: 90 Độ
- Vật liệu: Thép hợp kim
- Màu sắc: Đen
- Kiểu lắp đặt: Giá đỡ để bàn (C-Clamp hoặc Grommet)
- C-Clamp Độ dày bàn: 0.39" - 3.15"
- Grommet Mount Desk Thickness: 0.39" - 2.17"
- Đường kính lỗ khoen: 0.47" - 0.79"
Nội dung gói
Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.
- Main Pole with Desk Clamp/Grommet Base
- Vòng tay màn hình kép
- VESA Plates (2x)
- Mounting Hardware (screws, washers, tools)
- Clip quản lý cáp
- Hướng dẫn sử dụng
Thiết lập và cài đặt
1. Desk Compatibility Check
Before installation, ensure your desk meets the following criteria:
- Vật liệu: Recommended for wooden tables.
- Dưới: Preferably free of beams or panels that may interfere with installation.
- C-Clamp Độ dày: 0.39" - 3.15"
- Grommet Mount Thickness: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")
2. Monitor Compatibility Check
Each monitor must meet these conditions:
- Kích thước màn hình: 13 đến 34 inch
- Cân nặng: Lên đến 26.5 lbs
- Lỗ gắn VESA: 75x75 mm or 100x100 mm apart on the back of the monitor.
3. Assemble the Pole with Clamp Ủng hộ
Choose either C-Clamp or Grommet installation based on your desk type.
Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.
4. Assemble the Arm and Pole Wire Clips
Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.
5. Assemble VESA Plate and Monitor
Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.
6. Install the Monitor to the Swivel Arm
Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).
Vận hành và Điều chỉnh
The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewthoải mái:
- Điều chỉnh chiều cao: Nới lỏng clamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp một cách an toàn.
- Nghiêng: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
- Xoay: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewtừ những góc độ khác nhau.
- Sự xoay vòng: Xoay màn hình 360 độ để chuyển đổi giữa chế độ ngang và dọc.
- Duỗi/Thu cánh tay: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.
BẢO TRÌ
- Kiểm tra định kỳ tất cả các ốc vít và kết nối để đảm bảo chúng được siết chặt và an toàn.
- Làm sạch giá đỡ bằng vải mềm,amp vải. Tránh chất tẩy rửa mài mòn.
- Do not disassemble the mount unless instructed to do so.
Xử lý sự cố
- Màn hình không được đặt thẳng hàng: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
- Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
- Núi có cảm giác không ổn định: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.
Bảo hành và Hỗ trợ
For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.
