Xnbada RC03RF Wireless 2.4G RF 4 Zone RGB RGBW RGBCCT Smart Remote Control User Manual

1. Giới thiệu

This manual provides detailed instructions for the Xnbada RC03RF Wireless 2.4G RF 4 Zone Smart Remote Control. This remote is designed to control RGB, RGBW, and RGBCCT LED strip lights, offering versatile lighting adjustments through its 2.4G RF technology.

Nội dung gói hàng:

• 1 x RC03RF Remote Control
• 2 ốc vít (để gắn lên tường)

Figure 1: Xnbada RC03RF Remote Control and mounting screws.

2. Thông số kỹ thuật

3. Thiết lập

3.1 Lắp đặt pin

1. Xác định vị trí ngăn chứa pin ở mặt sau của điều khiển từ xa.
2. Mở nắp pin.
3. Lắp hai (2) pin AAA, đảm bảo lắp đúng cực (+/-).
4. Đóng chặt nắp pin.

Lưu ý: Pin không được bao gồm và phải mua riêng.

3.2 Pairing with Controllers

The RC03RF remote uses 2.4G RF technology for quick pairing without the need for Wi-Fi, Bluetooth, or a gateway. The pairing process typically involves the following steps:

1. Ensure your compatible LED controller (e.g., C03W, C04W, C05W) is powered on and connected to your LED strip lights.
2. On the LED controller, locate the pairing button (often labeled 'SET' or 'PAIR'). Press and hold this button for a few seconds until the connected LED strip lights flash or indicate pairing mode.
3. Within 15 seconds of the controller entering pairing mode, press one of the Zone ON buttons (1, 2, 3, or 4) on the RC03RF remote control.
4. The LED strip lights should flash again, indicating successful pairing.
5. Repeat this process for each zone you wish to control with a separate controller, or for multiple controllers within the same zone.

Figure 2: The RC03RF remote can control multiple LED strip controllers, with each zone button managing a distinct group of lights.

Figure 3: The remote control signal can be automatically transmitted to other controllers within 30 meters, extending the control range.

4. Hướng dẫn vận hành

4.1 Bố cục và chức năng của điều khiển từ xa

Figure 4: RC03RF Remote Control Button Functions.

• TRÊN, BẬT: Press to turn ON all linked devices.
• TẮT: Press to turn OFF all linked devices.
• Vòng màu: Touch the slider to select from 16 million colors and dim brightness from 1% to 100%.
• W: Press to switch between cool white, nature white, and warm white repeatedly.
• M (Chế độ): Press to cycle through dynamic modes.
• Tăng/Giảm độ sáng: Nhấn để tăng hoặc giảm độ sáng.
• Color Temp/Saturation Up/Down: Press to adjust color temperature or saturation.
• S-/S+ (Speed): Lower or accelerate dynamic mode speed.
• Zone ON/OFF (1-4): Press to turn ON/OFF specific zones or activate night light mode for a zone.

4.2 Color and Brightness Adjustment

• Lựa chọn màu sắc: Use the central color ring to select any of 16 million colors.
• Kiểm soát độ sáng: Adjust the brightness from 0% to 100% using the dedicated brightness buttons or by sliding on the color ring.
• Điều chỉnh ánh sáng trắng: Press the 'W' button to cycle through different white light temperatures (cool, natural, warm).
• 7 Pure Colors: The remote allows for one-key switching between 7 pure colors (red, orange, yellow, green, blue, purple, white).

Figure 5: Utilize the touch color ring for precise color selection from 16 million options.

Figure 6: Adjust brightness levels from 0% to 100% and activate night light mode.

Figure 7: Fine-tune the lighting with color temperature and saturation adjustments.

Kiểm soát vùng 4.3

The RC03RF remote allows you to control up to four independent zones of LED lights. Each zone can be controlled individually or grouped together.

• Kiểm soát từng khu vực riêng biệt: Press the corresponding Zone ON/OFF button (1, 2, 3, or 4) to control lights in that specific zone.
• All Zones Control: Use the Master ON/OFF buttons to control all paired zones simultaneously.

Figure 8: Manage lighting in up to four separate zones with dedicated buttons.

4.4 chế độ động

The remote includes various dynamic lighting modes. Press the 'M' button to cycle through these modes. Use the 'S-' and 'S+' buttons to adjust the speed of the selected dynamic mode.

5. Khả năng tương thích

The RC03RF remote control is compatible with the following Xnbada LED controllers:

• C03W (RGB Controller)
• C03Z (RGB Controller)
• C04W (RGBW Controller)
• C04Z (RGBW Controller)
• C05W (RGBCCT Controller)
• C05Z (RGBCCT Controller)
• WB5
• LM052
• LM053
• LM051

It is designed to control various LED strip light types, including COB, 5630, 5050, 3014, 5730, and 3528 LED strips.

Figure 9: A selection of compatible Xnbada LED controllers.

6. Bảo trì

6.1 Vệ sinh

To clean the remote control, use a soft, dry cloth. Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the surface or internal components.

6.2 Thay thế pin

When the remote's performance degrades or it stops responding, replace the two AAA batteries. Ensure proper polarity during installation.

6.3 Lưu trữ

Bảo quản điều khiển từ xa ở nơi khô ráo, thoáng mát, tránh ánh nắng trực tiếp và nhiệt độ quá cao hoặc quá thấp. Nếu cất giữ trong thời gian dài, hãy tháo pin ra để tránh rò rỉ.

KHAI THÁC. Xử lý sự cố

• Điều khiển từ xa không phản hồi:
  Check if the batteries are correctly installed and have sufficient charge. Replace batteries if necessary. Ensure the remote is within the 30-meter operating range of the controller. Re-pair the remote with the controller if the connection is lost.
• LEDs flickering:
  This can sometimes be caused by an unstable power supply to the LED controller. Ensure your power adapter provides stable voltage and sufficient current for your LED strips.
• Phạm vi điều khiển hạn chế:
  Obstacles such as thick walls or metal structures can reduce the effective range. Ensure there are no major obstructions between the remote and the controller. Minimize interference from other 2.4Ghz devices.
• Incorrect color display:
  Verify that the LED strip type (RGB, RGBW, RGBCCT) matches the controller and that the remote is correctly paired for that specific type.

8. Bảo hành và Hỗ trợ

For warranty information and technical support, please refer to the product packaging or contact Xnbada customer service directly. Keep your purchase receipt for warranty claims.