1. Giới thiệu
Thank you for choosing the Nissin i40 Flashgun for Nikon. This compact and powerful flash unit is designed to provide versatile lighting solutions for your photography needs. Please read this manual thoroughly before using the flashgun to ensure proper operation and to maximize its potential.
2. Thông tin an toàn
To prevent injury to yourself or others, or damage to the product, read all safety precautions before use. Keep this manual for future reference.
- Do not disassemble or modify the flashgun.
- Keep the flashgun away from water and moisture.
- Do not operate the flashgun in the presence of flammable gases or liquids.
- Avoid direct eye exposure to the flash light, especially at close range.
- Chỉ sử dụng các loại pin được chỉ định. Đảm bảo đúng cực khi lắp pin.
- Remove batteries if the flashgun will not be used for an extended period.
3. Sản phẩm hếtview
The Nissin i40 is a compact and lightweight flashgun offering a guide number of 40 (at 105mm, ISO 100). It features TTL, manual, and optical slave modes, a built-in diffuser, and a bounce card.
XUẤT KHẨU. Các thành phần
- Flash Head (rotates and tilts)
- Quay số điều khiển
- Nút chế độ
- Công tắc nguồn
- Ngăn chứa pin
- Đế giày nóng
- Bộ khuếch tán tích hợp
- Bounce Card
Note: Image URLs are placeholders as no specific image data was provided.
4. Thiết lập
4.1. Lắp pin
- Open the battery compartment cover located on the side of the flashgun.
- Insert four AA-size batteries (alkaline or Ni-MH rechargeable) according to the polarity indicators inside the compartment.
- Đóng chặt nắp ngăn chứa pin.
4.2. Gắn vào máy ảnh
- Ensure both the camera and flashgun are turned off.
- Slide the flashgun's hot shoe mount fully into the camera's hot shoe.
- Tighten the locking wheel on the flashgun to secure it in place.
5. Hướng dẫn vận hành
5.1. Bật/Tắt nguồn
To turn on the flashgun, slide the power switch to the "ON" position. To turn off, slide it to "OFF". The flashgun will automatically enter sleep mode after a period of inactivity to conserve battery power.
5.2. Lựa chọn chế độ
Nhấn nút CÁCH THỨC Nút này dùng để chuyển đổi giữa các chế độ đèn flash khác nhau:
- TTL (Qua ống kính): Tự động phơi sáng bằng đèn flash dựa trên phép đo sáng của máy ảnh.
- Hướng dẫn sử dụng (M): Manually set flash power output (1/1 to 1/256).
- SD (Slave Digital): Optical slave mode for digital pre-flash systems.
- SF (Slave Film): Optical slave mode for traditional single-flash systems.
5.3. Adjusting Flash Head
The flash head can be tilted upwards by 90 degrees and rotated horizontally by 180 degrees to the left and 90 degrees to the right for bounce flash photography.
5.4. Using Built-in Diffuser and Bounce Card
Pull out the wide-angle diffuser panel and the bounce card from the flash head as needed. The diffuser softens the light for wider coverage, while the bounce card helps direct light when bouncing off a ceiling.
Note: No relevant official product videos were found in the provided data to embed.
6. Bảo trì
Proper maintenance ensures the longevity and optimal performance of your Nissin i40 Flashgun.
- Clean the flashgun body with a soft, dry cloth. Do not use solvents or abrasive cleaners.
- Keep the hot shoe contacts clean and free of dust.
- Store the flashgun in a cool, dry place when not in use.
- Nếu cất giữ trong thời gian dài, hãy tháo pin ra để tránh rò rỉ.
KHAI THÁC. Xử lý sự cố
| Vấn đề | Nguyên nhân có thể | Giải pháp |
|---|---|---|
| Đèn flash không nháy. | Batteries are dead or incorrectly inserted. Flashgun not securely mounted. Flashgun is off. | Replace batteries or check polarity. Re-mount flashgun securely. Turn flashgun on. |
| Flash is too weak/strong. | Incorrect flash mode or power setting. ISO/aperture settings on camera. | Adjust flash power in Manual mode. Check camera settings. Ensure TTL is functioning correctly. |
| Flash does not sync with shutter. | Shutter speed too high (exceeds sync speed). | Reduce camera shutter speed to below or at the camera's maximum flash sync speed. |
8. Thông số kỹ thuật
| Tính năng | Chi tiết |
|---|---|
| Số hướng dẫn | GN40 (at 105mm, ISO 100) |
| Độ bao phủ tiêu cự | 24-105mm (16mm with built-in diffuser) |
| Nguồn điện | 4 x AA batteries (Alkaline, Ni-MH) |
| Thời gian tái chế | 0.1-4 seconds (approx.) |
| Chế độ Flash | TTL, Manual, SD, SF |
| Thời lượng Flash | 1/800 - 1/20000 giây |
| Kích thước (Rộng x Cao x Sâu) | 85 x 61 x 85 mm (xấp xỉ) |
| Cân nặng | 203g (không có pin) |
9. Bảo hành và Hỗ trợ
Nissin products are manufactured to the highest quality standards. This product comes with a limited warranty against defects in materials and workmanship from the date of purchase. Please refer to the warranty card included with your product for specific terms and conditions.
For technical support, service, or warranty claims, please contact your local authorized Nissin distributor or visit the official Nissin webđịa điểm:
