Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign User Manual

Model: EDG 1 R EL M6

1. Giới thiệu

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign. This edge-lit sign is designed for emergency egress lighting in commercial and institutional environments, ensuring clear visibility during power outagnghĩa là

The EDG 1 R EL M6 features a durable aluminum construction, energy-efficient LED illumination, and a reliable battery backup system. Adherence to these instructions will ensure proper function and compliance with safety standards.

2. Thông tin an toàn

Đọc bài hướng dẫn: Before beginning installation or maintenance, carefully read and understand all instructions provided in this manual.
Ngắt nguồn điện: Always disconnect power at the circuit breaker before installing, servicing, or cleaning the unit. Failure to do so may result in electric shock or serious injury.
Nhân viên có trình độ: Installation, servicing, and testing must be performed by qualified personnel in accordance with all national and local electrical codes and safety regulations.
Tuân thủ UL 924: This product is designed to meet UL 924 standards for emergency lighting and power equipment. Ensure all installations comply with these and other applicable standards.
Xử lý pin: The unit contains a sealed, maintenance-free nickel-cadmium battery. Do not attempt to open or service the battery. Dispose of batteries according to local regulations.
Điều kiện môi trường: Install in locations where ambient temperatures are within the specified operating range. Do not install near gas or electric heaters.

3. Nội dung gói hàng

Kiểm tra xem tất cả các thành phần đều có đầy đủ và không bị hư hỏng khi mở gói hàng:

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign (Battery-Powered, Red)
Mounting Hardware (typically includes screws, anchors, and canopy)
Instruction Sheet / Wiring Diagram

4. Thiết lập và Cài đặt

The EDG 1 R EL M6 is designed for surface mounting. Ensure the mounting surface is structurally sound and capable of supporting the fixture's weight.

4.1 Tùy chọn gắn kết

This unit supports various surface mounting configurations. Refer to the included wiring diagram for specific instructions on ceiling, wall, or end mounting.

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, red letters, top-down view.

Hình ảnh: Từ trên xuống view of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, showing the brushed aluminum housing and clear acrylic panel with red 'EXIT' letters.

4.2 Kết nối điện

Nguồn điện: The unit is dual voltage (120/277V). Connect the appropriate AC power supply wires to the fixture's input terminals as indicated in the wiring diagram.
Kết nối pin: Ensure the internal battery is properly connected after wiring the AC power. The battery is typically pre-connected but may require a final plug-in during installation.
Mức phí ban đầu: After installation and power connection, allow the unit to charge for a minimum of 24 hours before conducting any tests. This ensures the nickel-cadmium battery reaches full capacity.

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, red letters, side view.

Hình ảnh: Bên view of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, highlighting its slim profile and edge-lit design.

5. Hướng dẫn vận hành

The Lithonia Lighting EDG 1 R EL M6 operates automatically once properly installed and charged.

Hoạt động bình thường: When AC power is present, the LED 'EXIT' letters will be illuminated. The internal battery will continuously charge to maintain readiness for emergency operation.
Hoạt động khẩn cấp: In the event of an AC power failure, the unit will automatically switch to battery power, illuminating the 'EXIT' letters for a minimum of 90 minutes.
Nút kiểm tra: A test button is typically located on the side or bottom of the unit. Pressing this button simulates an AC power failure, allowing you to verify the emergency lighting function. The 'EXIT' letters should illuminate when the button is pressed and extinguish when released (assuming AC power is present).

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, red letters, front view.

Hình ảnh: Mặt trước view of the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign, clearly showing the red 'EXIT' letters.

6. Bảo trì

The EDG 1 R EL M6 is designed for low maintenance. However, regular checks are essential to ensure continued reliability.

Kiểm tra hàng tháng: Press the test button for at least 30 seconds to ensure the emergency lights operate.
Kiểm tra hàng năm: Disconnect AC power to the unit for a full 90-minute discharge test. The unit should remain illuminated for the entire duration. Reconnect AC power after the test.
Vệ sinh: Clean the exterior surfaces and acrylic panel with a soft, damp Lau chùi bằng vải. Không sử dụng chất tẩy rửa có tính ăn mòn hoặc dung môi. Đảm bảo đã ngắt nguồn điện trước khi vệ sinh.
Thay thế pin: The nickel-cadmium battery is maintenance-free and has a long lifespan. If the unit fails to hold a charge or operate for the required 90 minutes during testing, the battery may need replacement by qualified service personnel.
NFPA Compliance: All life safety equipment, including emergency lighting for paths of egress, must be maintained, serviced, and tested in accordance with all National Fire Protection Association (NFPA) and local codes.

KHAI THÁC. Xử lý sự cố

If your EDG 1 R EL M6 LED Emergency Exit Sign is not functioning as expected, refer to the following common issues and solutions:

Vấn đề	Nguyên nhân có thể	Giải pháp
'EXIT' letters do not illuminate during AC power failure.	Battery not charged or faulty; AC power not connected.	Ensure AC power is connected and allow 24 hours for initial charge. If problem persists, battery may need replacement.
'EXIT' letters do not illuminate when test button is pressed.	Battery not connected or faulty; unit not receiving AC power.	Verify AC power connection. Check battery connection. Allow 24 hours for charge.
Unit does not stay illuminated for 90 minutes during annual test.	Battery capacity reduced due to age or defect.	Battery needs replacement. Contact qualified service personnel.
'EXIT' letters are dim.	Low battery charge; dirty acrylic panel.	Allow unit to charge for 24 hours. Clean the acrylic panel.

For issues not listed above, or if troubleshooting steps do not resolve the problem, contact Lithonia Lighting customer support or a qualified electrician.

8. Thông số kỹ thuật

Detailed technical specifications for the Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign:

Số hiệu mẫu: EDG 1 R EL M6
Mã số sản phẩm: LTHEDG1RELM6
Nhà sản xuất: Ánh sáng Lithonia
Kích thước: Approximately 13 inches (Width) x 11.12 inches (Height)
Trọng lượng sản phẩm: 2.2 pound (1 kg)
Màu sắc: Red (letters)
Phong cách: Dùng pin
Hoàn thành: Chải nhôm
Vật liệu: Aluminum (housing), Acrylic (panel)
Nguồn điện: AC (for charging)
Tậptage: 120/277V (Dual Voltage)
Cái gì?tage: 3 watt
Loại bóng đèn: DẪN ĐẾN
Kiểu lắp đặt: Surface Mount (Ceiling, Wall, End)
Chứng nhận: Được UL niêm yết
Ắc quy: Sealed, maintenance-free Nickel-Cadmium
Emergency Operation Duration: Tối thiểu 90 phút
ĐÈN LED Lamp Mạng sống: Lên đến 100,000 giờ
Letter Height: 6 inch
Stroke Width: 3/4 inch
Viewing Khoảng cách: 100 feet (UL 924 standard)

Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign with dimensions: 13 inches wide, 8 inches high.

Image: Lithonia Lighting EDG 1 R EL M6 LED Emergency Exit Sign with key dimensions indicated.

9. Bảo hành và Hỗ trợ

For detailed warranty information, product registration, or technical support, please visit the official Lithonia Lighting webtrang web hoặc liên hệ với bộ phận chăm sóc khách hàng của họ. Giữ lại hóa đơn mua hàng để yêu cầu bảo hành.

Lithonia Lighting Customer Service: Vui lòng tham khảo thông tin liên hệ được cung cấp trên bao bì sản phẩm hoặc trang web chính thức của thương hiệu. webđịa điểm.

	Đèn chiếu sáng khẩn cấp bằng thép công nghiệp dòng ELT của Lithonia Lighting - Thông số kỹ thuật và đặt hàng Thông số kỹ thuật chi tiết, tính năng và thông tin đặt hàng cho các sản phẩm đèn chiếu sáng khẩn cấp bằng thép công nghiệp ELT16, ELT24, ELT36 và ELT50 của Lithonia Lighting. Bao gồm thông tin về điện, pin, lắp đặt và bảo hành.
	Hướng dẫn lắp đặt và bảo trì biển báo thoát hiểm LED cạnh Lithonia Lighting LRP/LRP2 Hướng dẫn lắp đặt, kiểm tra và bảo trì toàn diện cho Biển thoát hiểm khẩn cấp LED cạnh Lithonia Lighting LRP/LRP2 Series 120/277V, bao gồm các tùy chọn F, FA và FI có đèn nháy DC và tính năng báo động bằng âm thanh.
	Lithonia Lighting LED Combo Exit & Emergency Light Installation Instructions Comprehensive installation, operation, and maintenance guide for Lithonia Lighting's LED Combo Exit & Emergency Light, covering safety, mounting procedures, wiring, and battery backup.
	Lithonia Lighting ECBRM Quantum Running Man LED Light Bar Combo Unit - Emergency Lighting Specification Detailed specifications for the Lithonia Lighting ECBRM Quantum Running Man LED Light Bar Combo Unit, an emergency lighting fixture designed for path of egress illumination and marking. Includes features, construction, electrical, battery, installation, listings, warranty, ordering information, and spacing guidelines.
	Lithonia Lighting LED Combo Exit & Emergency Light Installation Instructions (EMCSA00802) Detailed installation instructions for the Lithonia Lighting LED Combo Exit & Emergency Light (Model EMCSA00802 Rev. F). Includes safety warnings, mounting procedures for back, top, and side installations, wiring diagrams, and operation details.
	Lithonia LED Combo Exit & Emergency Light Installation Instructions Comprehensive installation guide for the Lithonia LED Combo Exit & Emergency Light, covering safety warnings, installation procedures for various mounting types, operation details, maintenance, and wiring diagrams.