DIMPLEX CUH05B31T Compact Industrial Unit Heater Instruction Manual

1. Sản phẩm hếtview

The DIMPLEX CUH05B31T is a compact industrial unit heater designed for efficient heating in various indoor environments such as workshops and garages. It features a robust construction with a stainless-steel sheathed heating element, adjustable louvers for precise airflow direction, and a built-in single-pole bulb thermostat for temperature regulation. The unit also incorporates a fan-delay function to utilize residual heat and a power interrupt thermal cut-out for overheat protection.

Figure 1: DIMPLEX CUH05B31T Compact Industrial Unit Heater with mounting bracket.

2. Thông tin an toàn quan trọng

Read all instructions carefully before installing or using this heater. Failure to follow these instructions may result in fire, electric shock, personal injury, or property damage. Retain this manual for future reference.

• Lắp đặt điện: All electrical wiring and connections must be performed by a qualified, licensed electrician in accordance with national and local electrical codes.
• Nguồn điện: Hãy đảm bảo máy sưởi được kết nối với mạch điện 240V riêng biệt với các thiết bị phù hợp. amperage (typically 40A) and wire gauge (4-8 AWG copper wire).
• Tiếp đất: The heater must be properly grounded to prevent electrical shock.
• Khoảng cách: Maintain adequate clearance from combustible materials (walls, furniture, curtains, etc.) as specified in the installation section.
• Bảo vệ quá nhiệt: The unit is equipped with a power interrupt thermal cut-out that will automatically shut off the heater if it overheats. If this occurs, turn off the power, allow the unit to cool, and inspect for obstructions before restarting.
• Vị trí: Không lắp đặt máy sưởi ở những khu vực lưu trữ hoặc sử dụng xăng, sơn hoặc các chất lỏng dễ cháy khác.
• Độ ẩm: Do not expose the heater to water or excessive moisture. This unit is for indoor use only.

3. Nội dung gói hàng

Xác minh rằng tất cả các mục được liệt kê dưới đây đều có trong gói hàng của bạn:

• DIMPLEX CUH05B31T Unit Heater
• Giá đỡ xoay
• Installation Hardware (lag bolts, nuts, washers)
• Power Cord (pigtail)
• Hướng dẫn sử dụng

4. Cài đặt

4.1 Lắp đặt máy sưởi

The DIMPLEX CUH05B31T can be mounted on a ceiling or wall using the included swivel bracket. Ensure the mounting surface is structurally sound and capable of supporting the heater's weight (13.2 lbs) plus any additional stress from operation.

1. Select a suitable mounting location, ensuring proper clearances from combustible materials (refer to safety guidelines).
2. Attach the swivel mounting bracket to the chosen surface using the provided lag bolts and appropriate tools. Ensure the bracket is securely fastened.
3. Align the heater with the bracket and secure it using the large knobs on the sides of the unit. These knobs allow for adjustment of the heater's angle.
4. Tighten the smaller knobs to fix the heater at the desired angle. The bracket offers multiple angle positions for optimal heat distribution.

4.2 Kết nối điện

WARNING: Electrical installation must be performed by a qualified, licensed electrician. Ensure power is disconnected at the main circuit breaker before proceeding.

1. Locate the electrical access panel on the side of the heater. Remove the retaining screw and open the panel.
2. Identify the knockout on the side of the heater's casing. Use appropriate tools to remove the knockout.
3. Install the provided grommet with integral strain relief into the knockout opening.
4. Feed the power cord (pigtail) through the strain relief.
5. Connect the wires to the terminal block inside the heater:
• Connect the Black Wire to L1.
• Connect the Red Wire to L2.
• Connect the Green Wire to the Ground terminal.
6. Ensure all wire connections are secure and that no insulation is under the terminals.
7. Tighten the strain relief to prevent the power cord from pulling out or being damaged.
8. Close the electrical access panel and secure it with the retaining screw.

4.3 Adjusting Louvers

The heater features adjustable louvers on the front. These can be manually adjusted to direct the warm airflow to specific areas within your space. Gently move each louver to achieve the desired airflow pattern.

5. Hướng dẫn vận hành

The DIMPLEX CUH05B31T is equipped with a built-in single-pole bulb thermostat for temperature control and a fan delay function.

1. Bật nguồn: Ensure the heater is properly installed and connected to the power supply. Locate the main power switch/button (typically a red indicator) on the unit and turn it ON.
2. Cài đặt nhiệt độ: Use the built-in single-pole bulb thermostat to set your desired temperature. Rotate the thermostat dial to increase or decrease the temperature setting. The heater will operate until the set temperature is reached, then cycle on and off to maintain it.
3. Chức năng trì hoãn quạt: The fan delay function allows the fan to continue running for a short period after the heating element turns off. This utilizes residual heat, improving efficiency and ensuring all generated heat is distributed.
4. Bảo vệ quá nhiệt: In the event of overheating, the power interrupt thermal cut-out will activate, shutting down the heater. If this occurs, turn off the heater, allow it to cool down, and check for any obstructions to airflow before restarting.

6. Bảo trì

Bảo trì thường xuyên đảm bảo hiệu suất tối ưu và tuổi thọ của máy sưởi. Luôn ngắt nguồn điện trước khi thực hiện bất kỳ bảo trì nào.

• Vệ sinh: Định kỳ vệ sinh bên ngoài máy sưởi bằng vải mềm,amp cloth. Do not use abrasive cleaners or solvents. Ensure the air intake and exhaust areas are free from dust and debris.
• Kết nối điện: Annually, have a qualified electrician inspect all electrical connections for tightness and signs of wear or damage.
• mái che: Ensure the adjustable louvers move freely and are not obstructed.

KHAI THÁC. Xử lý sự cố

If your heater is not operating correctly, consult the following table for common issues and solutions. If the problem persists, contact a qualified electrician or DIMPLEX customer support.

8. Thông số kỹ thuật

9. Bảo hành và Hỗ trợ

This DIMPLEX CUH05B31T Compact Industrial Unit Heater comes with a 1-year warranty on the complete unit Kể từ ngày mua. Bảo hành này bao gồm các lỗi về vật liệu và tay nghề trong điều kiện sử dụng và vận hành bình thường.

For warranty claims, technical support, or service inquiries, please contact DIMPLEX customer support. Keep your proof of purchase for warranty validation.