GLOWRIUM LED Aquarium Light User Manual

1. Giới thiệu

This manual provides instructions for the GLOWRIUM LED Aquarium Light, Model GC035001. This full spectrum light is designed for freshwater planted tanks, featuring a remote control with an LCD display, an auto-timer function, and IP67 waterproofing. It includes dimmable RGB+W+Moon LEDs for customizable lighting environments.

2. Nội dung gói hàng

Xác minh rằng tất cả các mục được liệt kê dưới đây đều có trong gói hàng của bạn:

• GLOWRIUM LED Aquarium Light
• Điều khiển từ xa
• Bộ chuyển đổi
• Cáp nguồn
• Stand (Extendable Brackets)
• Hướng dẫn sử dụng (tài liệu này)

3. Thông tin an toàn

• Always unplug the light from the power outlet before performing any maintenance, cleaning, or installation.
• Ensure your hands are dry when handling the power adapter and plug.
• The light fixture is IP67 waterproof, meaning it is protected against temporary immersion in water. However, the power adapter and remote control are not waterproof and must be kept dry.
• Do not operate the light if any part is damaged, especially the power cord or adapter.
• Để xa tầm tay trẻ em.
• Đảm bảo thông gió thích hợp xung quanh đèn để tránh quá nhiệt.
• Điều khiển từ xa yêu cầu 2 pin AAA (không bao gồm).

4. Thiết lập

1. Đính kèm dấu ngoặc: Slide the extendable brackets onto the ends of the light fixture. Adjust the brackets to fit your aquarium's width. The brackets are designed to securely rest on the edges of your tank.
2. Đèn định vị: Place the light fixture with attached brackets securely on top of your aquarium. Ensure the light is centered and stable.
3. Kết nối nguồn: Connect the power cable to the light fixture, then connect the adapter to the power cable. Plug the adapter into a suitable power outlet.

Figure 4.1: Adjustable brackets and size compatibility chart. The light is designed to fit tanks from 12-17 inches (for the 9W model) up to 48-53 inches (for the 36W model) using its extendable brackets.

5. Hướng dẫn vận hành

5.1 Điều khiển từ xa Quaview

The GLOWRIUM LED Aquarium Light is operated using the included remote control with an LCD display. Ensure 2 AAA batteries are installed in the remote control. For optimal performance, direct the remote control towards the infrared receiver on the light fixture.

Figure 5.1: Remote control with LCD display. The display shows current time, sunrise/sunset settings, and individual RGBW channel percentagnghĩa là

5.2 Bật/Tắt nguồn

Nhấn nút BẬT/TẮT nút trên điều khiển từ xa để bật hoặc tắt đèn.

5.3 Auto-Timer Setting

The auto-timer allows for a 24/7 cycle with simulated sunrise and sunset. Once set, the light will operate automatically without further adjustments, even after a power interruption due to the built-in memory function.

1. Nhấn và giữ Bộ đếm thời gian button for three seconds to enter setup mode.
2. Sử dụng "+" Và "-" buttons to adjust the time value.
3. Sử dụng "<" Và ">" buttons to shift between parameters (current time, sunrise time, sunset time, and individual RGBW channel settings for each phase).
4. The light simulates a 30-minute sunrise (ramp up) and a 30-minute sunset (ramp down) based on your set times.

Figure 5.2: Auto-timer simulating natural sunrise and sunset cycles.

5.4 Điều chỉnh độ sáng

The light offers 10 levels of brightness adjustment.

• Sử dụng "+" Và "-" buttons (outside of timer setup mode) to increase or decrease the overall brightness.

Figure 5.3: Visual representation of 10-level brightness adjustment.

5.5 Spectrum Control (RGBW)

The light features dimmable RGB+W+Moon LEDs, allowing for full spectrum customization.

• Individual Channel Adjustment: Nhấn và giữ RGBW button for 3 seconds to adjust individual Red, Green, Blue, and White channels. Use the "+" Và "-" buttons to change the intensity of the selected channel. Use "<" Và ">" để chuyển đổi giữa các kênh.
• Preset Spectrums: The remote offers three preset spectrums: Thực vật (C1), Cá (C2), and Mặt trăng (C3). Press the corresponding button to activate.
• Custom Spectrums: You can save your customized RGBW settings to C1, C2, or C3 by adjusting the individual channels and then holding down the desired preset button (C1, C2, or C3) until the setting is saved.

Figure 5.4: Specially designed blue spotlight for moonlight mode or enhancing blue hues.

Hình 5.5: Ví dụamples of Plant and Fish preset lighting modes.

5.6 Video sản phẩm chính thức

Video 5.1: This video demonstrates the full spectrum capabilities and remote control functions of the GLOWRIUM LED Aquarium Light, including the auto-timer and color adjustments.

6. Bảo trì

• Vệ sinh: Regularly wipe the light fixture with a soft, damp cloth to remove dust, water spots, and algae buildup. Ensure the light is unplugged before cleaning. Do not use abrasive cleaners or solvents.
• Điều tra: Periodically check the power cord and adapter for any signs of damage. If damage is found, discontinue use and contact customer support.
• Điều khiển từ xa: Replace AAA batteries in the remote control when the display becomes dim or the remote's range decreases.

Figure 6.1: The IP67 waterproof design allows for safe cleaning of the light fixture.

KHAI THÁC. Xử lý sự cố

8. Thông số kỹ thuật

Figure 8.1: Detailed specifications for the GLOWRIUM LED Aquarium Light series.

9. Bảo hành và Hỗ trợ

GLOWRIUM provides a 2-year warranty for this product. We are committed to accepting returns and exchanges for any quality issues within the specified timeframe. For support or inquiries, please utilize our official after-sales channels. Our team is dedicated to honoring our commitment and assisting you with any product-related concerns.