JOCHEN Ebike Brushless Controller & Mini LCD S866 Display User Manual

Giới thiệu

This manual provides comprehensive instructions for the installation, operation, and maintenance of your JOCHEN Ebike Brushless Controller and Mini LCD S866 Display. This system is designed for electric bicycles and scooters, offering precise control and clear information display.

The 17A sine wave controller is compatible with both Hall and Hall-free brushless motors, suitable for 250W-350W electric bicycles and scooters. The color LCD CS866 intelligent display is compatible with 24V/36V/48V voltage systems and provides essential riding data.

Hình 1: Hếtview of the JOCHEN Ebike Brushless Controller, Mini LCD S866 Display, and Throttle.

Tính năng sản phẩm

• Bộ điều khiển sóng sin: The 17A sine wave controller ensures smooth and stable operation with reduced noise, compatible with 250W-350W brushless motors.
• Self-Learning Function: Features a white learning line on the controller to automatically detect the motor's phase angle and rotation direction, supporting both Hall and Hall-free motors.
• CS866 Intelligent Display: A color LCD display compatible with 24V/36V/48V systems, offering speed, remaining battery, subtotal mileage, and total mileage displays. Voltage can be adjusted via P03 parameter.
• Lamp Chức năng: The controller includes a red and black cable plug for connecting a lamp, providing power consistent with the battery voltage. Lights can be controlled by pressing and holding the up button on the display for 3 seconds.
• XT60 Plug: Equipped with an XT60 plug for power connection, featuring clear positive and negative pole signs. The plastic casing is made of insulating material for enhanced safety.

Figure 2: Key features of the controller, highlighting sine wave design for stable operation, the XT60 battery connector for safety, and the self-learning function.

Thiết lập và cài đặt

Carefully follow the wiring diagram to ensure correct installation. Incorrect wiring can damage the components.

Figure 3: Corresponding connection points for the 17A controller. Ensure each component is connected to its designated port.

Kết nối dây điện:

• Motor (9pin): Connect the motor cable to this port.
• Power (XT60): Connect your battery's XT60 plug here.
• Display (5pin): Connect the CS866 LCD display cable.
• PAS (3pin): Connect the Pedal Assist Sensor.
• Throttle (3pin): Kết nối bộ điều tiết ga.
• Brakes (2pin*2): Connect your brake levers.
• Lights (2pin*2): Connect your ebike lights. Note that this plug only provides power; an external switch or display control is needed to turn lights on/off.
• Self-study (1pin*2): Use these white learning lines for motor phase angle and rotation direction learning. Connect them briefly to initiate the learning process, then disconnect.

Display Wiring (TFT CS866):

The CS866 display uses a specific line sequence for communication. Refer to the diagram below for correct wiring if assembling individual components.

Figure 4: Instrument Line Sequence for the CS866 Display. This diagram shows the color coding for power, ground, and data lines.

• Vạch kẻ màu đỏ: cáp nguồn màn hình
• Đường màu xanh lam: Cáp bật/tắt nguồn bộ điều khiển
• Đường kẻ đen: Cáp nối đất hiển thị
• Green Line: Hiển thị dây nhận dữ liệu
• Đường kẻ màu vàng: Hiển thị dây gửi dữ liệu
• Light Line (White/Brown): White Line (GND), Brown Line (DD)

Hướng dẫn sử dụng

CS866 Display Functions:

The CS866 display provides various functions and settings for your ebike. It can display speed, battery level, mileage, and allows for parameter adjustments.

Hình 5: Hếtview of the CS866 Display's main functions and adjustable parameters.

Thao tác nút:

Figure 6: CS866 Display button layout and their corresponding functions.

• Nút '+':
  • Long press (3 seconds): Turn light on/off.
  • Short press: Increase PAS (Pedal Assist System) gear.
• Nút nguồn:
  • Long press (3 seconds): Turn display on/off.
  • Short press: Enter/confirm parameter settings.
• '-' Cái nút:
  • Short press: Decrease PAS gear.

Parameter Settings ('P' Parameters):

The display allows you to adjust various parameters to customize your riding experience. Press the Power button briefly to cycle through parameters. Use '+' and '-' to change values. Long press Power to save and exit.

Hình 7: Ví dụamples of parameter settings and error codes on the S866 display.

• P03 Parameter: Adjusts the corresponding voltage (24V/36V/48V) to match your battery.
• P06 Parameter (Wheel Size Setting): Set the correct wheel diameter for accurate speed and mileage readings.
• Other 'P' parameters may be available for advanced settings. Refer to the full display manual if provided separately for a complete list.

BẢO TRÌ

To ensure the longevity and optimal performance of your JOCHEN Ebike controller and display, follow these general maintenance guidelines:

• Keep all components clean and dry. Avoid exposure to excessive moisture or direct water spray.
• Regularly check all cable connections for tightness and signs of wear or corrosion. Ensure plugs are fully seated.
• Avoid subjecting the controller or display to extreme temperatures or direct sunlight for prolonged periods.
• Do not attempt to open the controller or display casing, as this may void the warranty and risk damage to internal components.
• Nếu cần làm sạch, hãy sử dụng miếng mềm, damp vải. Không sử dụng hóa chất mạnh hoặc chất tẩy rửa mài mòn.

Xử lý sự cố

If you encounter issues with your JOCHEN Ebike system, refer to the following common problems and solutions:

Display Error Codes ('E' Codes):

The display may show error codes to indicate specific problems. The character 'E' indicates a fault error.

• E07 (Motor Fault): This indicates an issue with the motor or its connection to the controller.
  • Check all motor phase wire connections and Hall sensor connections.
  • Ensure the motor is not obstructed.
  • Perform the self-learning function again (connect white learning lines briefly).
• E10 (Communications Receiving Error): This suggests a problem with the communication between the display and the controller.
  • Check the 5-pin display cable connection at both the display and controller ends.
  • Ensure the cable is not damaged or pinched.
• Display Does Not Turn On (DOA):
  • Verify that the battery is charged and properly connected to the controller's XT60 plug.
  • Check the 5-pin display cable connection.
  • Ensure the power button on the display is pressed and held for 3 seconds to turn on.
  • Xác nhận số lượng pintage is within the compatible range (24V/36V/48V) and P03 parameter is set correctly.
• Controller Runs Hot:
  • Ensure the motor is not overloaded or experiencing excessive resistance.
  • Verify that your battery's BMS (Battery Management System) can handle the current draw (e.g., 17A for this controller). An inadequate BMS can cause the system to shut off under load.
  • Đảm bảo thông gió thích hợp xung quanh bộ điều khiển.

Nếu sự cố vẫn tiếp diễn sau khi đã thử các giải pháp này, vui lòng liên hệ với bộ phận hỗ trợ khách hàng.

Thông số kỹ thuật

Figure 8: Dimensions of the 17A Brushless DC Motor Controller.

Figure 9: Product size details for the throttle, including its dimensions and SM plug wiring.

Thông tin bảo hành

This JOCHEN product comes with a Bảo hành 1 tháng from the date of purchase. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, misuse, accidents, unauthorized modifications, or normal wear and tear.

Hỗ trợ khách hàng

For any questions, technical assistance, or warranty claims, please contact the seller, LUDU Electric Bicycle Scooter Accessories Store, through the platform where you made your purchase. Provide your order number and a detailed description of the issue for prompt assistance.