Hướng dẫn sử dụng cảm biến cửa sổ/cửa ra vào không dây Ecolink WST-232 dành cho gia đình

Giới thiệu

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ecolink WST-232 Wireless Home Security Door Window Sensor. This device is designed to enhance the security of your home by detecting the opening and closing of doors and windows. It is compatible with Honeywell 5800 Wireless and 2GIG security systems.

Thông tin an toàn quan trọng

• Đọc kỹ tất cả các hướng dẫn trước khi cài đặt và sử dụng.
• Do not attempt to repair or modify the sensor. Refer all servicing to qualified personnel.
• Để pin xa tầm tay trẻ em. Vứt bỏ pin đã qua sử dụng đúng cách theo quy định của địa phương.
• Ensure the sensor is installed in a location where it will not be exposed to extreme temperatures or moisture.

Nội dung gói

Xác minh rằng tất cả các mục đều có trong gói hàng:

• Ecolink WST-232 Wireless Door/Window Sensor (Main Unit)
• Magnet (for contact detection)
• Mounting Hardware (screws, adhesive tape)
• Interchangeable Brown Case
• Hướng dẫn sử dụng (tài liệu này)

Sản phẩm trênview

The Ecolink WST-232 is a compact wireless sensor designed for monitoring the open/closed status of doors and windows. It features an internal reed switch for standard magnetic contact detection and an external contact input for connecting wired devices.

Hình ảnh: Ecolink WST-232 Wireless Door/Window Sensor showing the main unit and the external contact wires.

Các thành phần chính:

• Bộ phận cảm biến chính: Contains the battery, wireless transmitter, and internal reed switch.
• Nam châm: Triggers the internal reed switch when separated from the main unit.
• Nhập thông tin liên hệ bên ngoài: Two wires (typically red and black) for connecting an external wired contact.
• Ngăn chứa pin: Nằm ở phía sau của khối nhà chính.

Thiết lập và cài đặt

1. Lắp đặt pin

1. Open the sensor casing by gently prying it open from the side notch.
2. Insert the CR2032 lithium battery, ensuring the positive (+) side faces up.
3. Đóng cảm biến casing một cách an toàn.

2. Enrolling the Sensor with Your Security Panel

The WST-232 sensor is compatible with Honeywell 5800 Wireless and 2GIG security systems. Refer to your security panel's manual for specific enrollment procedures. General steps are as follows:

1. Put your security panel into programming mode for adding new wireless zones.
2. Activate the sensor by separating the magnet from the main unit, or by connecting/disconnecting the external contact wires. This sends a signal to the panel.
3. Confirm the sensor's serial number is learned by the panel.
4. Assign the sensor to an appropriate zone type (e.g., "Entry/Exit," "Perimeter").
5. Exit programming mode on your panel.

3. Lắp đặt cảm biến

Choose a suitable location on your door or window frame. The sensor and magnet should be mounted within 0.5 inches (1.27 cm) of each other when the door/window is closed.

Hình ảnh: Ecolink WST-232 sensor components including the main unit, magnet, and mounting screws.

Sử dụng vít:

1. Position the main sensor unit on the stationary frame and the magnet on the moving part (door/window).
2. Đánh dấu các lỗ vít.
3. Khoan lỗ dẫn hướng nếu cần thiết.
4. Secure both the sensor and magnet with the provided screws.

Using Adhesive Tape (not recommended for long-term security):

1. Clean the mounting surfaces thoroughly.
2. Apply adhesive tape to the back of the sensor and magnet.
3. Press firmly onto the desired surfaces for at least 30 seconds.

4. External Contact Input

The WST-232 includes an external contact input for integrating other wired devices, such as recessed door contacts or pressure mats. Connect the two wires from your external device to the red and black wires of the WST-232 sensor. The sensor will transmit a signal when the external contact opens or closes.

Vận hành cảm biến

Once installed and enrolled, the Ecolink WST-232 sensor operates automatically. When the door or window it is monitoring opens, separating the magnet from the main unit (or opening the external contact), the sensor will transmit a signal to your security panel. This signal indicates an "open" state. When the door or window closes, bringing the magnet back into proximity (or closing the external contact), the sensor transmits a "closed" state signal.

Your security panel will then react according to its programming (e.g., trigger an alarm if the system is armed, log the event).

BẢO TRÌ

Thay thế pin

The sensor uses one CR2032 lithium battery. When the battery level is low, your security panel will typically display a low battery warning for the corresponding zone. To replace the battery:

1. Put your security panel into disarm or test mode to prevent false alarms.
2. Nhẹ nhàng mở cảm biến casing.
3. Tháo pin CR2032 cũ ra.
4. Lắp pin CR2032 mới, đảm bảo đúng cực (+ hướng lên trên).
5. Đóng cảm biến casing một cách an toàn.
6. Test the sensor to ensure it communicates with the panel.

Vệ sinh

Clean the sensor and magnet with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the device.

Xử lý sự cố

Thông số kỹ thuật

• Người mẫu: WST-232
• Khả năng tương thích: Honeywell 5800 Wireless, 2GIG
• Kích thước: 3 x 1.7 x 1 inch (xấp xỉ)
• Ắc quy: 1 x CR2032 Lithium Coin Cell
• Tần suất hoạt động: 345MHz
• Nhà sản xuất: Ecolink Intelligent Technology Inc
• UPC: 657479755391

Bảo hành và hỗ trợ kỹ thuật

For warranty information and technical assistance, please refer to the official Ecolink webtrang web hoặc liên hệ trực tiếp với bộ phận hỗ trợ khách hàng của họ. Giữ lại hóa đơn mua hàng làm bằng chứng mua hàng.

Liên kết sinh thái Webđịa điểm: www.ecolink.com