How do I set the Finder 80.01.0.240.0000 modular timer for an 8-hour delay?

To set an 8-hour delay on the Finder 80.01.0.240.0000 modular timer, you must adjust the two rotary dials located on the front panel of the device. Please follow these steps:Step 1: Set the Time Scale (Multiplier): The device uses a combination of a range and a multiplier. Locate the dial that controls the time scale (often the smaller dial or a secondary setting on the 'T' dial depending on the specific sub-model revision). You need to select a range that includes 8 hours, such as the 24h or 10h scale.Step 2: Set the Time Value (T): Use the upper rotary dial labeled 'T' to point to the value that, when multiplied by your scale, equals 8. For example, if your scale is set to 10 hours, turn the 'T' dial to 8. If your scale is set to 24 hours, you would set the dial to approximately 1/3 of the way (since 8 is 1/3 of 24).Step 3: Select the Function: Ensure the lower rotary dial (labeled 'AI' or similar) is set to the correct timing function required for your application (e.g., ON-delay or OFF-delay).Note: Because this is an analog dial-based timer, the setting is an approximation. For critical applications requiring exact second-perfect timing over long periods like 8 hours, verify the timing with a stopwatch during the first cycle and fine-tune the 'T' dial as needed.

Hướng dẫn sử dụng bộ hẹn giờ đa chức năng dạng mô-đun Finder 80.01.0.240.0000

1. Giới thiệu

The Finder 80.01.0.240.0000 is a versatile modular multi-function and multi-voltage time delay relay from the 80 Series. This device is designed for precise timing control in various industrial and domestic applications, featuring a 16A Single Pole Double Throw (SPDT) output contact. Its modular design allows for easy integration into electrical panels.

2. Tính năng sản phẩm

Modular Multi-function Time Delay
Suitable for Timing Alternating & Sequencing Relay applications
Nhiều voltage operation (12...240V AC/DC)
16A SPDT output contact
Five selectable timing functions

3. Thông tin an toàn

Please read and understand all instructions before installing or operating this device. Failure to follow these instructions may result in electrical shock, fire, or serious injury. Installation and maintenance should only be performed by qualified personnel in accordance with all local and national electrical codes.

Luôn ngắt nguồn điện trước khi lắp đặt, đấu dây hoặc bảo trì.
Đảm bảo nguồn cung cấp voltage phù hợp với thông số kỹ thuật của thiết bị.
Do not exceed the maximum current rating of the output contacts.
Bảo vệ thiết bị khỏi độ ẩm, bụi và nhiệt độ khắc nghiệt.

4. Thiết lập và Cài đặt

The Finder 80.01.0.240.0000 timer is designed for DIN rail mounting. Ensure the mounting location is stable, free from vibrations, and provides adequate ventilation.

4.1. Lắp đặt

Securely attach the timer to a standard 35mm DIN rail.
Ensure sufficient space around the device for wiring and heat dissipation.

4.2. Hệ thống dây điện

Refer to the wiring diagram below and the markings on the device for correct connections. Use appropriate wire gauges for the current and voltage xếp hạng.

Finder 80.01.0.240.0000 Modular Timer showing terminals and control dials

Hình 1: Finder 80.01.0.240.0000 Modular Timer. This image displays the Finder 80.01.0.240.0000 modular timer. Visible elements include the power supply terminals A1 and A2 at the top, a control input B1, and output contacts 15, 16, and 18 at the bottom. The front panel features a time setting dial marked 'T' with values from 1 to 20, and a function selector dial labeled 'AI'. The operating voltage range 'Un 12...240V' and contact rating '16A 250V~' are also indicated.

A1, A2: Power Supply Terminals (Un 12...240V AC/DC). Connect the control voltage đây.
B1: Control Input. This terminal is used for specific timing functions (e.g., start/reset).
15: Common Contact for the SPDT output relay.
16: Normally Closed (NC) Contact. This contact is closed when the relay is de-energized and open when energized.
18: Normally Open (NO) Contact. This contact is open when the relay is de-energized and closed when energized.

5. Hướng dẫn vận hành

The timer features two rotary dials on the front panel for setting the timing function and the time delay value.

5.1. Lựa chọn chức năng

The lower rotary dial, labeled 'AI' (as seen in Figure 1), is used to select one of the five available timing functions. Refer to the product's detailed datasheet for a complete description of each function (e.g., ON-delay, OFF-delay, Flasher, etc.). Rotate the dial to align the desired function symbol with the indicator mark.

5.2. Cài đặt thời gian

The upper rotary dial, labeled 'T' (as seen in Figure 1), is used to set the time delay value. The dial typically has a range (e.g., 1 to 20 seconds, minutes, or hours) and a multiplier (e.g., '2s' for 2 seconds). Rotate the dial to the desired time value. The specific time range and multiplier depend on the model variant and selected function.

6. Bảo trì

The Finder 80.01.0.240.0000 timer is designed for long-term, maintenance-free operation under normal conditions.

Vệ sinh: If necessary, gently clean the exterior of the device with a dry, soft cloth. Do not use abrasive cleaners or solvents.
Điều tra: Kiểm tra định kỳ các kết nối dây điện để xem có chặt không và có dấu hiệu hao mòn hay ăn mòn không.
Môi trường: Đảm bảo môi trường hoạt động nằm trong phạm vi nhiệt độ và độ ẩm quy định.

KHAI THÁC. Xử lý sự cố

If the timer is not functioning as expected, consider the following common issues:

Không có điện: Check the power supply to terminals A1 and A2. Ensure the voltage is within the specified range (12...240V AC/DC).
Đấu dây không đúng: Verify all connections against the wiring diagram. Ensure terminals 15, 16, and 18 are correctly connected to the load.
Function/Time Setting: Confirm that the desired timing function and time delay are correctly set using the front panel dials.
Control Input (B1): If using a control input, ensure it is correctly wired and receiving the expected signal.
Quá tải: Check if the load connected to the output contacts exceeds the 16A rating.

If problems persist, contact Finder technical support or a qualified electrician.

8. Thông số kỹ thuật

Thuộc tính	Giá trị
Thương hiệu	Công cụ tìm kiếm
Số hiệu mẫu	80.01.0.240.0000
Vật liệu	Nhựa, Nhựa Resin
Hoạt động Voltage (Không)	12...240V AC/DC
Xếp hạng liên hệ đầu ra	16A 250V~ (SPDT)
Số cài đặt	5 (timing functions)
Trọng lượng sản phẩm	4.54 g (0.16 ounce)
Kích thước gói hàng	5 x 5 x 4 inch
Mã số UPC	758449164462
Nhà sản xuất	Công cụ tìm kiếm
Ngày đầu tiên có sẵn	Ngày 18 tháng 2020 năm XNUMX

9. Bảo hành và Hỗ trợ

For warranty information and technical support, please refer to the official Finder website or contact your authorized Finder distributor. Keep your purchase receipt for warranty claims.

Nhà sản xuất: Công cụ tìm kiếm

Webđịa điểm: www.finder-relays.com (Vui lòng xác minh thông tin chính thức) web(trang web dành cho khu vực của bạn)

Finder 80.01.0.240.0000