Giới thiệu
This manual provides essential information for the proper installation, operation, and maintenance of your iFlight 2.4G Receiver Antenna. This antenna is designed for use with compatible FrSky receivers and remote controllers, featuring a 150mm length and an IPEX 4 connector.
Please read these instructions carefully before use to ensure optimal performance and longevity of the product.
Tính năng sản phẩm
- Loại đầu nối: 2.4G receiver antenna with IPEX 4 Generation connector.
- Chiều dài: 5.9 inches (150mm) total length.
- Vật liệu: RF113 Silver plated Wire Material for enhanced signal transmission.
- Hiệu suất: Precision machining ensures low loss signal stability and high sensitivity.
- Khả năng tương thích: Specifically designed for FrSky XM+, X4R, and X4R-SB receivers, including mini versions.
Nội dung gói
The package contains 20 pieces of iFlight 150mm 2.4G Receiver Antennas.
Image: A bundle of iFlight 2.4G receiver antennas, showcasing the IPEX 4 connectors and the overall design.
Thiết lập và cài đặt
- Xác định loại kết nối: Ensure your receiver uses an IPEX 4 port. This antenna is designed for the smaller IPEX 4 connector. Refer to the comparison image below.
- Kết nối với máy thu: Carefully align the IPEX 4 connector of the antenna with the corresponding port on your FrSky receiver. Apply gentle, even pressure until you feel a distinct "snap," indicating a secure connection.
- Vị trí đặt ăng-ten: For optimal signal reception, position the antenna away from carbon fiber frames, metal objects, and other electronic components that may cause interference. Ensure the active element (the exposed wire tip) is not obstructed.
- Ăng-ten an toàn: Use heat shrink tubing, zip ties, or appropriate mounting solutions to secure the antenna in place, preventing it from moving during flight or operation. Avoid sharp bends or kinks in the antenna wire.
Image: A side-by-side comparison of the new IPEX 4 connector (smaller) and a regular IPEX connector (larger port), highlighting the difference.
Image: A FrSky receiver with an iFlight 2.4G receiver antenna properly connected. Note: The receiver is for reference only and not included with the antenna pack.
Hướng dẫn sử dụng
Once the antenna is securely connected and properly positioned, the receiver will utilize it for 2.4G signal reception from your remote controller. No specific operational steps are required for the antenna itself beyond proper installation.
Always perform a range check before operating your RC model to ensure reliable signal strength and control. Consult your receiver's manual for specific binding and range testing procedures.
BẢO TRÌ
- Kiểm tra thường xuyên: Periodically inspect the antenna wire and connector for any signs of damage, fraying, or corrosion.
- Độ sạch sẽ: Keep the antenna free from dirt, dust, and moisture. Use a soft, dry cloth for cleaning if necessary.
- Kho: When not in use, store the antennas in a dry, cool place, protected from physical damage.
- Thay thế: If the antenna wire is cut, bent severely, or the connector is damaged, replace it immediately with a new iFlight 2.4G Receiver Antenna to maintain signal integrity.
Xử lý sự cố
- Problem: Poor Signal / Frequent Failsafes
-
- Kiểm tra kết nối: Ensure the antenna is securely connected to the receiver's IPEX 4 port. A loose connection can severely degrade signal quality.
- Vị trí đặt ăng-ten: Verify that the antenna is positioned optimally, away from obstructions and interference sources. Ensure the active element is exposed.
- Hư hỏng ăng-ten: Inspect the antenna for any physical damage. Even minor cuts or kinks can affect performance. Replace if damaged.
- Các vấn đề về bộ thu: If multiple antennas show similar issues, the problem might lie with the receiver itself or the remote controller. Consult their respective manuals.
- Problem: Antenna Does Not Fit
-
- Xác minh loại kết nối: This antenna uses an IPEX 4 (smaller) connector. If your receiver requires a larger IPEX (U.FL) connector, this antenna will not be compatible. Double-check your receiver's specifications.
Thông số kỹ thuật
| Tham số | Giá trị |
|---|---|
| Số hiệu mẫu | 43234-1976 |
| Loại Ăng-ten | 2.4G Receiver Antenna |
| Loại đầu nối | IPEX 4 Generation |
| Chiều dài | 150mm (5.9 inch) |
| Vật liệu dây | RF113 Silver plated |
| Trở kháng | 50 Ohm |
| Dải tần số | 2400 - 2500 MHz |
| SWR | <= 2.0 |
| Nhận được | 2 |
| Nhiệt độ hoạt động | -40 °C đến +65 °C |
| Nhiệt độ lưu trữ | -40 °C đến +80 °C |
| Item Weight (per antenna) | Approximately 0.5g (as shown in product images) |
Image: The 150mm length of the antenna measured against a ruler.
Image: A single antenna on a digital scale, displaying a weight of 0.5 grams.
Video sản phẩm chính thức
Video: This official video demonstrates the 2.4G Receiver Antenna, highlighting its features and compatibility with Futaba and FrSky systems. (Duration: 0:24)
Bảo hành và Hỗ trợ
For warranty information and technical support, please refer to the official iFlight webtrang web hoặc liên hệ trực tiếp với bộ phận chăm sóc khách hàng của họ. Các điều khoản bảo hành cụ thể có thể khác nhau tùy theo khu vực và nhà bán lẻ.