Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack User Manual

Giới thiệu

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Performance Tool W1614 2 Ton (4,000 lbs.) Capacity Floor Jack. Designed for heavy-duty lifting tasks, this floor jack is constructed from durable steel and features swivel rear casters for easy positioning. It has a maximum lifting capacity of 4,000 pounds and can reach a maximum height of 15 inches.

Figure 1: Performance Tool W1614 2 Ton Floor Jack.

Thông tin an toàn

CẢNH BÁO: Sản phẩm này có thể khiến bạn tiếp xúc với các hóa chất bao gồm chì, được Tiểu bang California biết là có thể gây ung thư và dị tật bẩm sinh hoặc các tác hại sinh sản khác. Để biết thêm thông tin, hãy truy cập www.P65Warnings.ca.gov.

Always read and understand all instructions and warnings before using this floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Sử dụng trên bề mặt cứng, bằng phẳng: Luôn vận hành kích nâng trên bề mặt cứng, bằng phẳng và có khả năng chịu được tải trọng.
• Sử dụng Jack Stands: This floor jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Do not work under a vehicle supported only by a floor jack.
• Không vượt quá công suất định mức: Never exceed the 4,000 lbs. (2 Ton) rated capacity of this jack.
• Center Load on Saddle: Ensure the load is centered on the jack saddle to prevent slipping.
• Chock Wheels: Always chock the wheels that are not being lifted.
• Giữ khoảng cách: Keep hands, feet, and other body parts clear of moving parts and pinch points.
• Kiểm tra trước khi sử dụng: Before each use, inspect the jack for any damage, leaks, or loose parts. Do not use if damaged.
• Bảo vệ quá tải: This jack is equipped with an overload protection bypass valve for safety. Do not attempt to bypass or modify this feature.

Thiết lập và chuẩn bị ban đầu

Before first use, or if the jack has been stored for an extended period, it is important to bleed any air from the hydraulic system to ensure proper operation. Air in the system can cause the jack to lift unevenly or not lift at all.

Xả khí hệ thống thủy lực:

1. Locate the release valve. This is typically a screw or knob that controls the lowering function.
2. Lắp tay cầm vào ổ cắm tay cầm.
3. Xoay tay cầm ngược chiều kim đồng hồ để mở hoàn toàn van xả.
4. Pump the handle fully up and down approximately 10-15 times to force any trapped air out of the system.
5. Xoay tay cầm theo chiều kim đồng hồ để đóng van xả.
6. Test the jack by pumping the handle to raise the saddle. It should raise smoothly and evenly. If not, repeat the bleeding process.

Hình 2: Góc cạnh view of the floor jack, showing the handle socket and general structure.

Hướng dẫn sử dụng

Lifting a Vehicle:

1. Đỗ xe trên bề mặt cứng và bằng phẳng. Kéo phanh tay và chèn bánh xe không chạm đất.
2. Locate the vehicle's manufacturer-recommended lifting points. Refer to your vehicle's owner's manual.
3. Position the floor jack so that the saddle is directly under the lifting point. Ensure the load is centered on the saddle.
4. Close the release valve by turning the handle clockwise until it is firmly closed. Do not overtighten.
5. Pump the handle up and down to raise the vehicle to the desired height. Lift only high enough to place jack stands.
6. Immediately place appropriately rated jack stands under the vehicle's designated support points.
7. Slowly open the release valve by turning the handle counter-clockwise to lower the vehicle onto the jack stands. Once the vehicle is securely resting on the jack stands, remove the floor jack.

Lowering a Vehicle:

1. Ensure the area around the vehicle is clear of obstructions and personnel.
2. Position the floor jack saddle directly under the vehicle's lifting point, adjacent to the jack stands.
3. Pump the jack handle a few times to slightly raise the vehicle off the jack stands.
4. Cẩn thận tháo giá đỡ kích ra khỏi gầm xe.
5. Slowly turn the jack handle counter-clockwise to open the release valve. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
6. Once the vehicle is fully lowered, remove the floor jack.

Figure 3: Diagram showing key dimensions and lift range of the floor jack.

BẢO TRÌ

• Bôi trơn: Thường xuyên bôi trơn tất cả các bộ phận chuyển động bằng dầu máy nhẹ.
• Chất lỏng thủy lực: Check the hydraulic fluid level regularly. If low, add high-quality hydraulic jack oil. Do not use brake fluid or other types of oil.
• Vệ sinh: Hãy giữ cho kích nâng xe luôn sạch sẽ, không bám bụi bẩn, dầu mỡ và các mảnh vụn.
• Kho: Store the jack in a dry, clean place with the ram fully retracted to prevent rust and extend seal life.
• Điều tra: Regularly inspect for any signs of wear, damage, or leaks. If any issues are found, do not use the jack and have it serviced by qualified personnel.

Xử lý sự cố

Thông số kỹ thuật

Bảo hành và Hỗ trợ

For specific warranty information, please refer to the documentation included with your purchase or contact Performance Tool customer service. Keep your purchase receipt for warranty claims.

Bạn có thể tải xuống Sách hướng dẫn sử dụng chính thức (dưới dạng PDF): Tải xuống Hướng dẫn sử dụng (PDF)

For technical support or inquiries, please visit the official Performance Tool webtrang web hoặc liên hệ với bộ phận dịch vụ khách hàng của họ.